Globalcontractor's Blog

Industrial Property Development

Posts Tagged ‘turbine

NIAGARA Development seeks buyer of “On-Site Power Generation and Utilities”!

leave a comment »

With the various economic incentives, prospective manufacturers, possibility of supplying electricity behind the meter, or with a complete rebuild to sell electricity to the grid (using one of the many BIO-Fuels benefit programs), one could quickly negotiate with NIAGARA Worldwide to get the recently shut down facility, bought, leased or managed.


Contact us today to set up a site walk and process review:
Eric J Spirtas – President NIAGARA Worldwide LLC – 314.780.3742 – eric.spirtas@niagaraworldwide.com


Steam Production

The New Page mill has (4) four 75,000 lb per hour coal fired power boilers (located in building 45) that produce process steam for drying paper, heating water, heating the buildings and producing power. Coal is delivered by truck from the Escanaba lakefront dock to an on-site storage yard, which has a 10,000 ton storage capacity.  The coal is then processes through a crushing and screening system (located in building 97), where it is sized for use dependent on the boiler being supplied (stoker or pulverized coal fired).  Two of the four boilers also have the ability to burn wood waste as a supplemental fuel.  Wood waste is produced on-site in the PGW fiber pulping process and also purchased locally.  All four boilers are ducted through a common state of the art electrostatic precipitator (building 90) and electrostatically enhanced baghouse to control particulate emissions.  The baghouse was installed in 2006 at cost of 7.5 million dollars and is considered the best available control technology (BACT) for particulate matter control.


Filtered Water

The Menominee River
is the main source of water for the paper mill. A pumping station (located in building 57) draws water from the river and pumps it to the water filtration plant (located in building 56) where it is treated for suspended solids and color.  The plant capacity is approximately 7.2 million galloons per day.


Waste Water Treatment

Waste water is treated by means of two different processes.  An aerobic facility (buildings 89, 93, and 104) treats low BOD process waters at a maximum average capacity of 8 million gallons per day.


Waste Water Treatment
(Continued)

An anaerobic treatment facility (building 99) pre-treats high BOD process waters at a rate of 1.5 million gallons per day.  Solids from the treatment facility’s are concentrated using two Andritz presses (building 103) and then spread on local farming land.

Utility Department Process details

Steam Generation

Typical Monthly Totals

Total steam produced:  132.4 mm lbs.

Boilerhouse auxiliary:  12.4 mm lbs.

Steam turbines:  24.3 mm lbs.

Process:  95.7 mm lbs.

#1 Boiler

1939 combustion engineering water tube boiler

Steaming capability

75,000 lb/hour 80% efficient (coal)

450 lb. steam @ 675 deg.

Fuel used – pulverized coal

15,000 tons of coal per year

2 – CE Raymond 372 bowl mills

New Ro type burners in 1996

6” wide x 10’ long x 8’ tall dutch ovens that burn 14,250 tons of bark per year

Bark produces 30 to 35 K/Lb/hour

wood waste:  70% efficient

2 five million BTU natural gas ignitors for lighting off the coal

#2 Boiler

1939 combustion engineering water tube boiler

Steaming capability

75,000 lb/hour 80% efficient

450 lb. steam @ 675 deg.

Fuel used – pulverized coal

15,000 tons of coal per year

One CE-Raymond 453 bowl mill

Installed in 1997

New Ro type burners in 1996

2.6’ wide x 10’ long x 8’ tall dutch ovens that burn 14,250 tons of bark per year

Bark produces 30 to 35 K/Lb/hour

Wood waste:  70% efficient

2 five million BTU natural gas ignitors for lighting off the coal

 

#3 Boiler

1948 combustion engineering water tube boiler

Steaming capability

75,000 lb/hour 85.5% efficient

450 lb steam @ 675 deg.

Fuel used – pulverized coal

27,000 tons of coal per year

CE Raymond 453 bowl mill

DCS Bailey Infi 90 installed in 1999

2 five million BTU natural gas igniters for lighting off the coal

#4 Boiler

1963 Babcock & Wilcox Detroit roto-grate stoker

Steaming capability

75,000 lb/hour 86.1% efficient

450 lb steam @ 675 deg.

Fuel used – 1 ¼” x 3/8” stoker coal

Coal fed into boiler by three Detroit roto-grate stokers

23,000 tons per year  

Controls

All boilers and auxiliaries are controlled by a Bailey DCS system

#2 boiler in 1997

Auxiliaries in 1998

#1 boiler in 1998

#4 boiler in 1998

#3 boiler in 1999

Coal Crusher

Designed to run 50 tons per hour of run of mine coal (6” x 0” or 5” x 3/8”)

Gunlach Machine Company double stage crusher

Coal crusher building

Crushes the coal into two categories (2” x 1 ¼” and 3/8” x 0”)

All coal is sent to a double deck vibrating screen where the sizing takes place

Stoker coal 1 ¼” to 3/8” goes to #4 boiler

Coal 2” to 1 ¼” and 3/8” to 0” goes to pulverized coal boilers #1-2-3

Stocker coal pile – 8,724 tons

Stoker coal is stored in a 60 ton silo until use

Coal storage area can hold 10,000 tons of coal

 

Coal Specifications

Heating value – 13,000 BTU/lb. (min 12,500 BTU/lb)

Ash content – target 7.5% maximum 8.5%

Moisture – 5% maximum

Sulpher range – 0.8% to 1.8%, 2% maximum at 13,000 BTU/lb.

Grind – 50 to 55 HGI

Volatile matter – 35% to 38% based on fuel specification

Fixed carbon – 19% to 52% based on fuel specification

Ash fusion – target 2,300 Deg. F ID

 

Bark Handling System

Drag type conveyor system that handles 14 tons of bark per hour

All of the woodbark (15,000 tons/year) that is blown to us, plus what we receive from an outside supplier (42,355 tons/year)

All wood waste is burned in boilers #1 & 2 dutch ovens

Produce 30 to 35 K/Lb/hr in each boiler from wood wastes

3.15 pounds of steam per pound per bark

Ash Handling System

Two ash silos

South silo

Unloader is rotary drum type (1962)

Collects ash from all 4 boilers

Bark furnaces back end and fly ash

Dry ash handling system

North ash silo

Unloader is from United Conveyor Model 1535/45 twin paddle mixer

Ash comes from the precipitator, ash hoppers under each field

Dry ash handling system

All ash hauled to a company owned solid landfill site

Precipitator

1974 electrostatic precipitator with one common stack from all four boilers

Four fields have weighted wires in the first three fields

Fourth field installed in 1997 with riged discharge electrodes

Controlled by a precip-tech SQ-300 automatic voltage controllers

Efficiency is 99.8% at zero opacity

Baghouse

GE Max 9 baghouse installed in 2006

Electrostatic enhanced

First of its type in operation

Nine modules, 1188 bags

Maximum temperature is 500 degrees F

300,000 Acfm gas volume

Clarage #173 5450 RHW ID fan

86 ½” diameter

300,00 CFM, 20” S.P. 450 degrees F

1250 HP, 1200 RPM ID fan motor with spare

Variable hydraulic Gyrol drive with spare

Howden size 315 class 4

Internal pump geared for 1200 RPM


Power Generation

The FERC hydro project number 2536-009 has been sold to Northbrook Energy

Raw Water Supply System

Basin Capacities

Quick mix basin – 24,000 gallons

Flocculation basin – 80,000 gallons

Settling basin – 2,000,000 gallons

Clearwell – 600,000 gallons

Six filter beds – 392 ft2 each

Raw Water Supply Pumps

Primary – Two vertical 3500 GPM pumps per 250 HP motors

Backup – One pump, 7500 GPM

Chemical Feed Systems

40-80 ppm alum at raw water pump discharge – dosage dependent on river water quality and temperature

0-2.0 ppm coagulant polymer (alum replacement) at raw water pump discharge

0-2.0 ppm flocculent polymer at discharge of quick mix basin

10:1 ratio NaOC1:NaBr added at feed to filter beds – closed loop ORP control to 780 target

Chemical Storage Tanks

Filter plant

850 gallon flocculent polymer

2 tanks 2500 gallons each – sodium hypochlorite

2 tanks 1500 gallons each – sodium bromide

Pump house

1500 gallons coagulant polymer

8000 gallons alum

Powerhouse

1500 gallons coagulant polymer

Sludge Removal

DCS operated zone valves remove sludge from settling basin to sludge pit

40 HP sludge pump empties sludge pit to effluent plant sewer

Each filter bed backwashed once per day

50,000 gallons per filter

Backwash recycled automatically to quick mix basin – 300,000 gallons per day

Process Description

The process is controlled by the Bailey DCS

The primary pumps are supplied from a 40,000 tank located under the powerhouse – Two sources supply this tank

In winter, warm water from #2 turbine condenser (8000 gpm) is reclaimed for heat value

Any additional makeup (100% during summer months) is provided by a 20” line from the penstock

Alum and coagulant polymer are added at the pump discharge for good mixing

The raw water is pumped through a 16” heat traced line to the quick mix basin at the filter plant

A flocculent polymer is added at the discharge of the quick mix basin as the water enters the flocculation basin

Solids settle in the settling basin and the water is disinfected as it enters the filter beds

From the filter beds, the water enters the clear well for distribution to the mill

Each filter is backwashed once per day for approximately five minutes at 10,000 gpm

In-line meters track the turbidity before and after the filters

Disinfection is controlled by an ORP controller

Filters

Leopold underdrain with Integral Media Support Cap

10” silica sand

14” filter anthracite

Air scouring headers on 4 of 6 filters

Environmental

Anaerobic Pre-Treatment Facility

Purpose:  To treat high BOD process waters

Neutralization tank (175,000 gallons) – combination of high BOD waste waters and waste-activated biosolids from the aeration system

Two anaerobic reactors (2,450,000 gallons each)

Degas tank (34,800 gallons)

Gravity clarifier (734,000 gallons)

Settled biosolids aer split into two streams, one stream is sent to the dewatering plant (80 gpm) and one stream is returned to the anaerobic reactors (600 gpm)

Effluent from clarifier is sent to aerobic treatment facility (1,500,000 gallons per day)

Biosolids Dewatering Plant

Purpose:  To concentrate biosolids for use in the Niagro program or for landfill

Two Andritz presses (400 gpm maximum capacity each) – settled biosolids from the anaerobic plant clarifier are combined with underflow solids from the primary clarifier in the aerobic treatment facility

Average production:  250 gpm, 30 dry tons per day

Aerobic Treatment Facility

Purpose:  To treat low BOD process waters, effluent from the anaerobic plant and effluent from the dewatering plant

Primary clarifier (2,460,000 gallons)

Average flow into clarifier 6,500,000 gallons per day (5.5 million in winter and 7.5 million in summer)

Underflow solids sent to dewatering plant

Overflow sent to aeration tanks

Two aeration tanks (40,000 gallons & 871,000 gallons)

Two rectangular secondary clarifiers (945,000 gallons & 1,081,000 gallons)

Settled solids are split into two streams, one stream is sent to the anaerobic plant (250 gpm) and one stream is returned to the aeration tanks (9200 gpm)

Effluent is sent to the Menominee River (6,000,000 gallons per day average)


Contact us today to set up a site walk and process review:
Eric J Spirtas – President NIAGARA Worldwide LLC – 314.780.3742 – eric.spirtas@niagaraworldwide.com

Advertisements

General Electric Steam Turbine 9375KW Generator with Condenser

with one comment

PRIVATE TREATY OFFERING
Former Niagara “NewPage” Mill – Equipment Sales
Contact:  Eric J. Spirtas TODAY – 314.780.3742 ericspirtas@ejspirtasgroup.com

EQUIPMENT TYPE:        

STEAM TURBINE 9375kw

Specific Name – General Electric Steam Turbine Generator with Condenser

 

Turbine No. 164030


Generator No. 8328468
– 9375KW –  2 Poles
3600rpm –  60 Cycles
–  14 Stage –  Air Cooled
–  450 PSIG –  4160 V
–  Temp. 675 F –  KVA:  12500
–  Exhaust Pressure 2.0 in HG ABS –  Stator Amperes:  1735
  –  Field Amperes:  158

STEAM CONDITIONS:  

–  Throttle:                      Mt = 135kpph
–  Extraction:                  Mext = 77kpph
–  Absolute pressure:    (Barometric pressure) – (Turbine vacuum)
–  Throttle:                      Header pressure = 427
–  Extraction:                  53.6 psi
–  Absolute pressure:    PO = 29.96-27.6 = 2.36Hg absolute
–  Throttle:                      Header temperature = 670 degrees F.
–  Extraction:                  347 degrees F.
–  Power output :           8756KW   78% efficiency

ATTACHMENTS: 

–  Design Data
–  Performance Curves
–  Steam Path Drawing
–  Mechanical Drawing

 

The CUT SHEET above as well as the attached PDF prints and diagrams are for a specific system or piece of equipment.

Please note that we have a massive amount of OTHER EQUIPMENT for your review and pricing (a sample of items are listed below).

Also available for sale are the complete STORES, WAREHOUSE, TOOLS, BEARINGS MACHINE SHOP and  CARPENTRY SHOP.

In addition, ROLLING STOCK and LICENSED VEHICLES will be offered.

We are handling sales on an INTERNATIONAL basis, by direct negotiation.  Offers are being received regularly and equipment is being sold.

Site visits, Rigging, Hauling, Payment Terms and other details can be discussed directly with Eric J. Spirtas – 314.780.3742

WOODROOM / PGW
NUM  COMPONENT DESCRIPTION QTY
1 DEBARKER Nicolson A5A  22″ 1
2 DEBARKER Manitowoc 1
3 GRINDERS Tampella T1812 4
4 GRINDER MOTORS EM 7000HP AC 327rpm 5
5 PRESSURIZED DISC THIKENER Hedemora 1
6 STOCK CONTROL SYSTEM Bailey Infi 90 20
7 PRIMARY COURSE SCREEN Bird 400  0.032″ slots 2
  PRESSURE SCREEN In PGW (North East Bay) 1
  PRESSURE SCREEN Basket In PGW (North East Bay) 1
8 SECONDARY SCREEN Ahlstrom F2   0.032″ slots 1
9 AIR COMPRESSOR Gardner Denver ElectraSaver 1
10 PORTABLE CRANE 4000lb. Owantona Tool Co. 1
11 SELF PRIMING PUMP Gorman T-Series centrifugal 1
12 CITY WATER PUMP Syncoflo 2
13 WELDER Lincoln Arc 1
14 OILING SYSTEM Vickers Lube DoubleA Hydpum 1
15 HYDRAULIC SYSTEM Atlas Cepco/Sperry Vickers 1

PAPER MACHINE
NUM  COMPONENT DESCRIPTION QTY
1 #43 HEADBOX Voith W-7500 max12400gpm 1
2 #43 COUCH VACUUM                                                   (2)Siemens2BE3,Nash L-10 3
3 #43 SUCTION PICK UP VACUUM SOURCE Siemens 2BE3,Liquid Ring 2
4 #43FIRST PRESS VACUUM Nash CL-9002,(2) Siemens 3
5 #43 SUCTION FELT VACUUM Nash 904-S1 2
6 #43UHLE BOXES Vacuum Siemens,Nash CI_9002 2
7 #43 COATED DRYING Solaronics gas fired 5 rows 5
8 #43 FAN PUMP Goulds 3420 low-pulse 1
9 #43 FAN PUMP MOTOR ABB   945hp/875rpm 1
10 #43 PRESSURE SCREEN Bird 50 .047″Alstrom basket 1
11 #43TAILINGS SCREEN Jonsson vibrating 39.5×55″ 2
12 #43COATING SUPPLY FILTERS Ronningen-Petter 5
13 #44HEADBOX Voith W-8500 1
14 #44COUCH VACUUM Siemens 2BE3,Liquid Ring 1
15 #441ST PRESS VACUUM Siemens 2BE 1605 1
16 #442ND PRESS VACUUM Siemens 2BE 1606 1
17 #44 COATING SUPPLY FILTERS Ronningen-Petter DCF-2000 4
18 #44THICKSTOCKSCREENING Black Clawson .008″ 3 stage 1
19 #44BLEND CHEST PUMP Goulds #3175 15″dia. Impeller 1
20 #44MACHINECHEST PUMP Goulds #3175 17.75dia. Imp. 1
21 #44FAN PUMP Goulds#3420 split low pulse 1
22 #44TAILING SCREENS Jonsson vibrating 39.5×55″ 2
23 #44 PRESSURE SCREEN Voith 31 .047″rotor3rows 9van 1

STOCK PREP
NUM  COMPONENT DESCRIPTION QTY
1 REFINER Beloit 42″ DD4000 1
  MOTOR Louis Allis 1500 horse AC 1
2 REFINER Sprout Waldron   42″ 1
  MOTOR   1
  MOTOR In North Mill 2
3 REFINER Sprout Bauer 34″ R-34TF III 1
  MOTOR   1
4 REFINER                                                     Beloit 20″ (Rebuilt by J&L) 2
5 WET LAP Andritz Hymac 100″ twin wire press 1
6 SCREW PRESS Thune SP45L      134″ 1
7 TWIN WIRE PRESS Andritz 2.6 Meter  (145tpd) 300t twp 2
8 DRUM WASHER Impco / 4 shower heads per drum 2
9 REPULPER Voith Sulzer   344tpd 1
10 BROKEPULPER Voith Sulzer  with Guillotine 1

ELECTRICAL
NUM  COMPONENT DESCRIPTION QTY
1 MOTOR CONTROL CENTERS Allen Bradley Centerline 32
2 MOTOR CONTROL CENTERS Cutler Hammer IT 1
3 MOTOR CONTROL CENTERS Cutler Hammer Freedom 6
4 MOTOR CONTROL CENTERS Cutler Hammer Unitrol 15
5 MOTOR CONTROL CENTERS Furnas System 89 3
6 MOTOR CONTROL CENTERS Furnas System 89 1
7 MOTOR CONTROL CENTERS GE 8000 Line 6
8 MOTOR CONTROL CENTERS GE 7700 Line 9
9 480 VOLT AC MOTORS 10-2100 HP 941
10 460VOLT AC MOTORS  10-200HP 72
11 125 VOLT AC MOTOR 2500HP 1
13 4160 VOLT AC MOTORS 200-1300 HP 45
14 575 VOLT AC MOTOR 945 HP 1
15 500 VOLT DC MOTORS 10-800HP 76
16 600 VOLT DC MOTOR 1000 HP 1

SPECIALTY
NUM  COMPONENT DESCRIPTION QTY
1 DEWIRE/DESTACK Advanced Dynamics 1
2 ROLL GRINDER Cincinnati   50×338″ 1
3 LATHE LeBlond  19″swingx144″ 1
4 LATHE LeBlond  1
5 JAGENBERG VARI-ROLL WINDER Unwind 110″dia. 6200fpm 1
6 STEAM TURBINE/GENERATOR GE 12MW 450#/50#/cond 1
7 SLUDGE PRESS Andritz  30dtpd 2
8 PULVERIZER CE-Raymond  372 2
9 PULVERIZER CE-Raymond 453 1
10 CHEMICAL MIXER Andritz HCM3HH 300hp motor 1
11 MOTOR for Andritz Unit 300hp 1
12 AUGER for Andritz Unit   1

Regards

EJ
Eric J. Spirtas
NIAGARA Development, LLC

Site Address:
1101 Mill Street
Niagara Wisconsin, 54151

Offices:
11469 Olive Blvd – Suite #124
Creve Coeur, MO 63141
314.780.3742 Direct
314.432.2429 Fax
ericspirtas@ejspirtasgroup.com
www.ejspirtasgroup.com

Written by globalcontractor

December 4, 2010 at 7:56 pm

Posted in Paper Machine Equipment

Tagged with , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Wet Lap – Kavaerner Hymac Inc. Twin Wire Press – Cutter Layboy with Conveyor Line

leave a comment »

PRIVATE TREATY OFFERING
Former Niagara “NewPage” Mill – Equipment Sales
Contact:  Eric J. Spirtas TODAY – 314.780.3742 ericspirtas@ejspirtasgroup.com

EQUIPMENT TYPE:

Wet Lap  Equipment

EQUIPMENT TYPE:  
Wet Lap Kavaerner Hymac Inc. Twin Wire Press & Cutter Layboy with Conveyor Line

Specific Name                      
Kavaerner Hymac Inc. Twin Wire Press & Cutter Layboy with conveyor line

Model                                    
Press – Model 100HP-SF-031MS, Cutter Layboy – Model CL-100

Dimensions                          
100” Working Width

Age / Condition                  
MFG 1993, Rebuilt by Andritz in 2000, Well Maintained

OPERATING DATA:     
Press Capacity                      200 BDSTPD
Press Inlet % Con                s. 3.5-4.0
Press Outlet % Cons.           4.2-4.7, Temperature 50-120 F.
Sheet Handling Rate           125 BDSTPD
Sheet  Size                             50” X 37”
Bale Height                           48” X 60”
Bale Weight                          3000lbs

ATTACHMENTS:             
Twin Wire Press Information
Cutter & Layboy Information
Proof of 2000 Rebuild
Wet Lap Drawings

The CUT SHEET above as well as the attached PDF prints and diagrams are for a specific system or piece of equipment.

Please note that we have a massive amount of OTHER EQUIPMENT for your review and pricing (a sample of items are listed below).

Also available for sale are the complete STORES, WAREHOUSE, TOOLS, BEARINGS MACHINE SHOP and  CARPENTRY SHOP.

In addition, ROLLING STOCK and LICENSED VEHICLES will be offered.

We are handling sales on an INTERNATIONAL basis, by direct negotiation.  Offers are being received regularly and equipment is being sold.

Site visits, Rigging, Hauling, Payment Terms and other details can be discussed directly with Eric J. Spirtas – 314.780.3742

WOODROOM / PGW
NUM  COMPONENT DESCRIPTION QTY
1 DEBARKER Nicolson A5A  22″ 1
2 DEBARKER Manitowoc 1
3 GRINDERS Tampella T1812 4
4 GRINDER MOTORS EM 7000HP AC 327rpm 5
5 PRESSURIZED DISC THIKENER Hedemora 1
6 STOCK CONTROL SYSTEM Bailey Infi 90 20
7 PRIMARY COURSE SCREEN Bird 400  0.032″ slots 2
  PRESSURE SCREEN In PGW (North East Bay) 1
  PRESSURE SCREEN Basket In PGW (North East Bay) 1
8 SECONDARY SCREEN Ahlstrom F2   0.032″ slots 1
9 AIR COMPRESSOR Gardner Denver ElectraSaver 1
10 PORTABLE CRANE 4000lb. Owantona Tool Co. 1
11 SELF PRIMING PUMP Gorman T-Series centrifugal 1
12 CITY WATER PUMP Syncoflo 2
13 WELDER Lincoln Arc 1
14 OILING SYSTEM Vickers Lube DoubleA Hydpum 1
15 HYDRAULIC SYSTEM Atlas Cepco/Sperry Vickers 1

PAPER MACHINE
NUM  COMPONENT DESCRIPTION QTY
1 #43 HEADBOX Voith W-7500 max12400gpm 1
2 #43 COUCH VACUUM                                                   (2)Siemens2BE3,Nash L-10 3
3 #43 SUCTION PICK UP VACUUM SOURCE Siemens 2BE3,Liquid Ring 2
4 #43FIRST PRESS VACUUM Nash CL-9002,(2) Siemens 3
5 #43 SUCTION FELT VACUUM Nash 904-S1 2
6 #43UHLE BOXES Vacuum Siemens,Nash CI_9002 2
7 #43 COATED DRYING Solaronics gas fired 5 rows 5
8 #43 FAN PUMP Goulds 3420 low-pulse 1
9 #43 FAN PUMP MOTOR ABB   945hp/875rpm 1
10 #43 PRESSURE SCREEN Bird 50 .047″Alstrom basket 1
11 #43TAILINGS SCREEN Jonsson vibrating 39.5×55″ 2
12 #43COATING SUPPLY FILTERS Ronningen-Petter 5
13 #44HEADBOX Voith W-8500 1
14 #44COUCH VACUUM Siemens 2BE3,Liquid Ring 1
15 #441ST PRESS VACUUM Siemens 2BE 1605 1
16 #442ND PRESS VACUUM Siemens 2BE 1606 1
17 #44 COATING SUPPLY FILTERS Ronningen-Petter DCF-2000 4
18 #44THICKSTOCKSCREENING Black Clawson .008″ 3 stage 1
19 #44BLEND CHEST PUMP Goulds #3175 15″dia. Impeller 1
20 #44MACHINECHEST PUMP Goulds #3175 17.75dia. Imp. 1
21 #44FAN PUMP Goulds#3420 split low pulse 1
22 #44TAILING SCREENS Jonsson vibrating 39.5×55″ 2
23 #44 PRESSURE SCREEN Voith 31 .047″rotor3rows 9van 1

STOCK PREP
NUM  COMPONENT DESCRIPTION QTY
1 REFINER Beloit 42″ DD4000 1
  MOTOR Louis Allis 1500 horse AC 1
2 REFINER Sprout Waldron   42″ 1
  MOTOR   1
  MOTOR In North Mill 2
3 REFINER Sprout Bauer 34″ R-34TF III 1
  MOTOR   1
4 REFINER                                                     Beloit 20″ (Rebuilt by J&L) 2
5 WET LAP Andritz Hymac 100″ twin wire press 1
6 SCREW PRESS Thune SP45L      134″ 1
7 TWIN WIRE PRESS Andritz 2.6 Meter  (145tpd) 300t twp 2
8 DRUM WASHER Impco / 4 shower heads per drum 2
9 REPULPER Voith Sulzer   344tpd 1
10 BROKEPULPER Voith Sulzer  with Guillotine 1

ELECTRICAL
NUM  COMPONENT DESCRIPTION QTY
1 MOTOR CONTROL CENTERS Allen Bradley Centerline 32
2 MOTOR CONTROL CENTERS Cutler Hammer IT 1
3 MOTOR CONTROL CENTERS Cutler Hammer Freedom 6
4 MOTOR CONTROL CENTERS Cutler Hammer Unitrol 15
5 MOTOR CONTROL CENTERS Furnas System 89 3
6 MOTOR CONTROL CENTERS Furnas System 89 1
7 MOTOR CONTROL CENTERS GE 8000 Line 6
8 MOTOR CONTROL CENTERS GE 7700 Line 9
9 480 VOLT AC MOTORS 10-2100 HP 941
10 460VOLT AC MOTORS  10-200HP 72
11 125 VOLT AC MOTOR 2500HP 1
13 4160 VOLT AC MOTORS 200-1300 HP 45
14 575 VOLT AC MOTOR 945 HP 1
15 500 VOLT DC MOTORS 10-800HP 76
16 600 VOLT DC MOTOR 1000 HP 1

SPECIALTY
NUM  COMPONENT DESCRIPTION QTY
1 DEWIRE/DESTACK Advanced Dynamics 1
2 ROLL GRINDER Cincinnati   50×338″ 1
3 LATHE LeBlond  19″swingx144″ 1
4 LATHE LeBlond  1
5 JAGENBERG VARI-ROLL WINDER Unwind 110″dia. 6200fpm 1
6 STEAM TURBINE/GENERATOR GE 12MW 450#/50#/cond 1
7 SLUDGE PRESS Andritz  30dtpd 2
8 PULVERIZER CE-Raymond  372 2
9 PULVERIZER CE-Raymond 453 1
10 CHEMICAL MIXER Andritz HCM3HH 300hp motor 1
11 MOTOR for Andritz Unit 300hp 1
12 AUGER for Andritz Unit   1

Regards

EJ
Eric J. Spirtas
NIAGARA Development, LLC

Site Address:
1101 Mill Street
Niagara Wisconsin, 54151

Offices:
11469 Olive Blvd – Suite #124
Creve Coeur, MO 63141
314.780.3742 Direct
314.432.2429 Fax
ericspirtas@ejspirtasgroup.com
www.ejspirtasgroup.com

Thune Press Dewatering Screw Press SP 45L

leave a comment »

PRIVATE TREATY OFFERING
Former Niagara “NewPage” Mill – Equipment Sales
Contact:  Eric J. Spirtas TODAY – 314.780.3742 / ericspirtas@ejspirtasgroup.com

EQUIPMENT TYPE:

Thune Press 

Specific Name                               
Thune dewatering screw press SP 45L
 

Description                    
“L” model,  long unit with pre-drainer section
 

Dimensions
4.16 meters overall
 

Condition
Installed in 1980, well maintained
 

Material Type
Stainless steel
 

OPERATING DATA:
Capacity Data on Site 

ATTACHMENTS:              
Mechanical Drawing
Proof of Make and Model

 Thune Front Side View

 

Thune Back Side View

 

Thune Name Plate

The CUT SHEET above as well as the attached PDF prints and diagrams are for a specific system or piece of equipment.

Please note that we have a massive amount of OTHER EQUIPMENT for your review and pricing (a sample of items are listed below).

Also available for sale are the complete STORES, WAREHOUSE, TOOLS, BEARINGS MACHINE SHOP and  CARPENTRY SHOP.

In addition, ROLLING STOCK and LICENSED VEHICLES will be offered.

We are handling sales on an INTERNATIONAL basis, by direct negotiation.  Offers are being received regularly and equipment is being sold.

Site visits, Rigging, Hauling, Payment Terms and other details can be discussed directly with Eric J. Spirtas – 314.780.3742.

WOODROOM / PGW
NUM  COMPONENT DESCRIPTION QTY
1 DEBARKER Nicolson A5A  22″ 1
2 DEBARKER Manitowoc 1
3 GRINDERS Tampella T1812 4
4 GRINDER MOTORS EM 7000HP AC 327rpm 5
5 PRESSURIZED DISC THIKENER Hedemora 1
6 STOCK CONTROL SYSTEM Bailey Infi 90 20
7 PRIMARY COURSE SCREEN Bird 400  0.032″ slots 2
  UNKNOWN PRESSURE SCREEN In PGW (North East Bay) 1
  UNKNOWN PRESSURE SCREEN Basket In PGW (North East Bay) 1
8 SECONDARY SCREEN Ahlstrom F2   0.032″ slots 1
9 AIR COMPRESSOR Gardner Denver ElectraSaver 1
10 PORTABLE CRANE 4000lb. Owantona Tool Co. 1
11 SELF PRIMING PUMP Gorman T-Series centrifugal 1
12 CITY WATER PUMP Syncoflo 2
13 WELDER Lincoln Arc 1
14 OILING SYSTEM Vickers Lube DoubleA Hydpum 1
15 HYDRAULIC SYSTEM Atlas Cepco/Sperry Vickers 1

PAPER MACHINE
NUM  COMPONENT DESCRIPTION QTY
1 #43 HEADBOX Voith W-7500 max12400gpm 1
2 #43 COUCH VACUUM                                                   (2)Siemens2BE3,Nash L-10 3
3 #43 SUCTION PICK UP VACUUM SOURCE Siemens 2BE3,Liquid Ring 2
4 #43FIRST PRESS VACUUM Nash CL-9002,(2) Siemens 3
5 #43 SUCTION FELT VACUUM Nash 904-S1 2
6 #43UHLE BOXES Vacuum Siemens,Nash CI_9002 2
7 #43 COATED DRYING Solaronics gas fired 5 rows 5
8 #43 FAN PUMP Goulds 3420 low-pulse 1
9 #43 FAN PUMP MOTOR ABB   945hp/875rpm 1
10 #43 PRESSURE SCREEN Bird 50 .047″Alstrom basket 1
11 #43TAILINGS SCREEN Jonsson vibrating 39.5×55″ 2
12 #43COATING SUPPLY FILTERS Ronningen-Petter 5
13 #44HEADBOX Voith W-8500 1
14 #44COUCH VACUUM Siemens 2BE3,Liquid Ring 1
15 #441ST PRESS VACUUM Siemens 2BE 1605 1
16 #442ND PRESS VACUUM Siemens 2BE 1606 1
17 #44 COATING SUPPLY FILTERS Ronningen-Petter DCF-2000 4
18 #44THICKSTOCKSCREENING Black Clawson .008″ 3 stage 1
19 #44BLEND CHEST PUMP Goulds #3175 15″dia. Impeller 1
20 #44MACHINECHEST PUMP Goulds #3175 17.75dia. Imp. 1
21 #44FAN PUMP Goulds#3420 split low pulse 1
22 #44TAILING SCREENS Jonsson vibrating 39.5×55″ 2
23 #44 PRESSURE SCREEN Voith 31 .047″rotor3rows 9van 1

STOCK PREP
NUM  COMPONENT DESCRIPTION QTY
1 REFINER Beloit 42″ DD4000 1
  MOTOR Louis Allis 1500 horse AC 1
2 REFINER Sprout Waldron   42″ 1
  MOTOR   1
  MOTOR In North Mill 2
3 REFINER Sprout Bauer 34″ R-34TF III 1
  MOTOR   1
4 REFINER                                                     Beloit 20″ (Rebuilt by J&L) 2
5 WET LAP Andritz Hymac 100″ twin wire press 1
6 SCREW PRESS Thune SP45L      134″ 1
7 TWIN WIRE PRESS Andritz 2.6 Meter  (145tpd) 300t twp 2
8 DRUM WASHER Impco / 4 shower heads per drum 2
9 REPULPER Voith Sulzer   344tpd 1
10 BROKEPULPER Voith Sulzer  with Guillotine 1

ELECTRICAL
NUM  COMPONENT DESCRIPTION QTY
1 MOTOR CONTROL CENTERS Allen Bradley Centerline 32
2 MOTOR CONTROL CENTERS Cutler Hammer IT 1
3 MOTOR CONTROL CENTERS Cutler Hammer Freedom 6
4 MOTOR CONTROL CENTERS Cutler Hammer Unitrol 15
5 MOTOR CONTROL CENTERS Furnas System 89 3
6 MOTOR CONTROL CENTERS Furnas System 89 1
7 MOTOR CONTROL CENTERS GE 8000 Line 6
8 MOTOR CONTROL CENTERS GE 7700 Line 9
9 480 VOLT AC MOTORS 10-2100 HP 941
10 460VOLT AC MOTORS  10-200HP 72
11 125 VOLT AC MOTOR 2500HP 1
13 4160 VOLT AC MOTORS 200-1300 HP 45
14 575 VOLT AC MOTOR 945 HP 1
15 500 VOLT DC MOTORS 10-800HP 76
16 600 VOLT DC MOTOR 1000 HP 1

SPECIALTY
NUM  COMPONENT DESCRIPTION QTY
1 DEWIRE/DESTACK Advanced Dynamics 1
2 ROLL GRINDER Cincinnati   50×338″ 1
3 LATHE LeBlond  19″swingx144″ 1
4 LATHE LeBlond  1
5 JAGENBERG VARI-ROLL WINDER Unwind 110″dia. 6200fpm 1
6 STEAM TURBINE/GENERATOR GE 12MW 450#/50#/cond 1
7 SLUDGE PRESS Andritz  30dtpd 2
8 PULVERIZER CE-Raymond  372 2
9 PULVERIZER CE-Raymond 453 1
10 CHEMICAL MIXER Andritz HCM3HH 300hp motor 1
11 MOTOR for Andritz Unit 300hp 1
12 AUGER for Andritz Unit   1

Regards

EJ
Eric J. Spirtas
NIAGARA Development, LLC

Site Address:
1101 Mill Street
Niagara Wisconsin, 54151

Offices:
11469 Olive Blvd – Suite #124
Creve Coeur, MO 63141
314.780.3742 Direct – 314.432.2429 Fax
ericspirtas@ejspirtasgroup.com
www.ejspirtasgroup.com